RoverRoger Cheng2018US
Sawppy the Rover
Hobbyist motorized model of the Curiosity/Perseverance rovers with rocker-bogie suspension, built from aluminum extrusion, 3D-printed parts and serial bus servos.
Difficulty index
5.4/13| Class | rover | +1.5 |
|---|---|---|
| Cost | $260 BOM | +0.4 |
| DOF | unknown · midpoint | +1.5 |
| Parts | 1451 parts | +2 |
Specimen photographs
1 itemSawppy the Rover Conquers a BackpackRoger Cheng · official video, embedded · source
Spec card
4/13 known- Price
- $500 · ~$500 parts budget
- BOM total
- $260 · 4/41 lines priced
- Part count
- 1451
- Actuators
- Serial bus servos
Not in the registry: degrees of freedom, height, mass, payload, speed, runtime, battery, compute, sensors. Left blank rather than guessed.
What you learn building it
- +Differential drive and odometry
- +Battery sizing and power budgets
- +Reading IMUs, encoders and range sensors
- +Navigation and mapping
- +FDM 3D printing: 167 parts, about 220 h of printing
- +Tools used: FDM printer with at least a 200 x 200 mm bed (a Monoprice Maker Select was used; PETG may need an all-metal hot end), Drill with 8 mm reamer, 4 mm (5/32 in) drill bit, M3 tap, Soldering iron, M3 x 10-14 mm bolt, washer and hex key, C-clamp or arbor press, Saw that cuts aluminium (or order Misumi cut-to-length) +11
- +19 assembly steps across 7 subassemblies
- +Flashing firmware for Raspberry Pi 3 (SGVHAK_Rover Flask web UI, Python), LewanSoul LX-16A x10 via BusLinker USB serial (IDs 20-29 in the reference build), Optional: Arduino Nano (arduino_sawppy wired control)
Openness
- publicCAD
- publicBOM
- publicFirmware
- not publicSim model
- publicSoftware
- not publicPolicies
Score 70/100 computed from what is public: CAD 25, BOM 20, sim 20, firmware 15, software 10, policies 10. Hardware license: MIT. Software license: MIT.
Repos & models
Build it
Has an ORP build package.- BOM total
- $260
- Lines priced
- 4/41
- Parts
- 1451
- Steps
- 19
- Version
- 0.1.0
37 lines have no price yet, so the real total is higher.
Largest BOM lines
| Part | Qty | Unit |
|---|---|---|
| LewanSoul/Hiwonder LX-16A serial bus servo (6 drive, 4 steering)LX-16A | 10 | $15 |
| Filament, 1 kg spools (about 3 kg for all parts; PETG for final parts) | 3 | $25 |
| 2-cell (2S) LiPo battery, 5200 mAh 30C RC pack used | 1 | $25 |
| LewanSoul BusLinker / debug board (USB to serial bus servo interface) | 1 | $10 |
| Raspberry Pi 3 Model B (3B+ or Pi 4 should also work) | 1 | ? |
| microSD card (SanDisk Extreme 32 GB used) | 1 | ? |
| Battery connector (Deans T plug) | 1 | ? |
| LiPo balance charger (Tenergy TB6-B used) | 1 | ? |
Fabrication
- FDM 3D printing167
- Print time (listed)220 h
Assembly time in the step graph: about 6 h.
Firmware repo- USD figures are the author's rough $500 budget ('Price breakdown', in USA prices): servos 10 x $15, BusLinker $10, 2S LiPo $25, filament 3 x $25, Misumi cut extrusions $42.32. Other parts (bearings $20, turnbuckles $10, misc hardware $75, electronics $20, Pi $50) are only group budgets, so those lines carry no unit price. Prices outside the US are reported to be higher.
- Most vendor links are Amazon (US) short links from an Amazon Associates page; some go to generic category results. Misumi outside the US mostly sells to businesses only; MakerBeamXL or AliExpress 15 mm beams are alternatives.
- Shafts need grooves and flat detents cut by the builder (lathe or drill-and-Dremel); there is no purchasable shaft kit. Only the 300 mm differential rod must be steel.
- The fuse rating conflicts: the docs README says 10 A, the Amazon parts page says a 5 A fuse.
- The Parts List marks Rocker Body Mount as mirrored while its print page says it is symmetric. Battery Tray and Power Panel have STLs but no print or assembly page. The price breakdown lists $10 of laser-cut acrylic for the equipment bay, but no cut file is in the repo.
- SGVHAK_Rover targets Python 2.7 (RoboClaw API constraint) and the Pi access-point instructions link an old raspberrypi.org page; expect to adapt on current Raspberry Pi OS. The Sawppy doc refers to 'config_sawppy.json', but the file in SGVHAK_Rover is config_roverchassis.json.sawppy.
- The author describes V1 electronics and software as 'very immature' and parts of V1 as left to builder preference; the V2 and Micro Sawppy designs are separate projects and not covered here.
- Only per-print durations are published (PETG final times used for printHours); no torque values. Total filament about 3 kg.
- Links in the repo README point at tree/master, but the repository's default branch is main.
Simulate
humanoidrobots.training/sawppy/sawppy
No public URDF or MJCF.
Next rung
SO-101 (SO-ARM101) →The Robot Studio / Hugging Face · arm · index 3.7Easiest buildable arm, the next class up from rover. Adds forward and inverse kinematics.
NoteInspired by JPL OSR. Repo documents 'Sawppy V1'; last pushed Sep 2025. City from maker's GitHub profile. V1 control software is SGVHAK_Rover (MIT, Python 2.7-era). Video: Sawppy climbing demo at Sparklecon VII, on the maker's New Screwdriver channel.
Sources
- [1]SGVHAK_Rover (Sawppy V1 software, MIT)checked 2026-09-25
- [2]YouTube oEmbed: 'Sawppy climbing demo at Sparklecon VII' by New Screwdriverchecked 2026-09-25
- [3]Sawppy repo (MIT)checked 2026-09-24
- [4]Hackaday.io projectchecked 2026-09-24